First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it’s overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”.

How do I reset my washing machine motor?

  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
  3. The motor has now been reset and is ready for you to start a cycle.

What does OL mean on Kenmore Elite washer?

The OL code means an overload has been detected by the main control. Worse case scenario is the overload error is being triggered by a bearing in the outer tub. The bearing may be causing extra drag that the control interprets as being caused by an overloaded washer.

How do I reset my Whirlpool Cabrio washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do you fix the UL code on a Maytag washer?

  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
  3. The motor has now been reset and is ready for you to start a cycle.

Why does my Whirlpool Cabrio washer keep saying uL?

If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.

What is Whirlpool Cabrio?

Whirlpool Cabrio 4.3 Cu. … 12-Cycle High-Efficiency Top-Loading Washer: Give clothes a deep clean and gentle care with this Whirlpool top-loading washer. The large capacity fits more in a single load and makes it easy to wash bulky items like comforters.

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

What does OL mean on a Whirlpool Cabrio washer?

The OL error code indicates that the washer is overloaded. If the washer is not overloaded, this would indicate either a drag on the drive system or the control board is failing. Be sure nothing is on the floor under the washer that could be causing a problem.

Article first time published on

Why is my Whirlpool Cabrio washer not draining?

Check the washer’s discharge hose if the water fails to drain from the washtub. Look for any kinks in the Cabrio washer’s discharge hose that could stop the water from draining. Straightening the hose ensures proper draining. … Test the drain pump to ensure it has not failed if the washer still will not drain.

How do you reset a Kenmore Elite washer?

  1. Press the “Stop” button twice, and then press the “Power” button. Video of the Day.
  2. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
  3. Press the “Start” button to complete the reset process and restart the washing machine.

How do I run diagnostics on my Kenmore Elite washer?

  1. With the washer empty, close the door.
  2. Push “control/on” or “Start”
  3. Select “Drain/Spin”
  4. Select “No Spin” by pressing SPIN SPEED touchpad.
  5. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
  6. C:00 should light up and begin the diagnostic.

How do you reset a Kenmore Elite Oasis washer?

The only way to reset a washer, is to disconnect it from the outlet or switch off the designated home circuit breaker for 20-30 minutes, then restore the power. If the washer won’t drain then it will not be able to go into spin so if you fix the no drain problem the spin problem may take care of itself.

What does OL mean on a Maytag washer?

Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.

Why does my washing machine keep going off balance?

Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.

What is the life expectancy of a Whirlpool Cabrio washer?

Whirlpool also says the lifespan of a Cabrio washer is 11 1/2 years, that’s comical, if you’re easily entertained by bad jokes.

How long should a Whirlpool Cabrio washer last?

How long will it last? Top loaders typically have a longer life than front load washing machines. This model should last about 14 years.

What brand is Cabrio?

The Whirlpool brand, maker of the Duet and Cabrio model, is a leader in washer and dryer sales in the United States.

How do you reset a Whirlpool washing machine?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

How do I put my Whirlpool washer in diagnostic mode?

Press the 1st button you used to enter the Duet Diagnostics Mode. Now that you are in the Duet washer interface test you can press each button one time. when a button is pressed the button’s indicator light should turn on and you should get a beep.

Why does my washer stop mid cycle?

If a washer stops mid-cycle, it could be because the pump or the motor that runs it has failed. When this happens, it cannot remove the water efficiently, pump water in, and thus the sensors won’t allow it to move to the next cycle.

What are common problems with washing machines?

  • It Bounces Around. …
  • It’s Noisy. …
  • Clothes Are Getting Ripped. …
  • Improper Or Slow Draining. …
  • My Washing Machine Won’t Spin. …
  • There’s No Water. …
  • The Door Won’t Open. …
  • It’s Smelly.

How do I know if I need a new motor for my washing machine?

If your washing machine fails to start or makes strange noises, it could be the motor. The motor operates the drum and pump. Motors should last a long time, but when they do go out, it usually is due to poor maintenance. However, just because the motor fails doesn’t mean it is the problem.

How much does it cost to replace a washing machine motor?

Washing Machine Motor Repair Cost If a part of the motor, like the coupling, just needs to be fixed, the cost may be under $100. However, a washing machine motor replacement cost runs an average of $325 to $500.

How long does a washing machine motor last?

Unless it’s a high-end model and has a particular appeal to you, Consumer Reports doesn’t recommend replacing any appliance that’s more than eight years old.

What is the F70 code on Whirlpool washer?

The F70 error on this model washer is a central control unit (CCU) heartbeat failure. This means there is communication loss from the central control unit and the user interface. … If all the wiring and connections look good and the drum on the washer rotates replace the user interface.