​1. RK Racing Chain 520-SO-120 120-Links O-Ring Chain with Connecting Link.RK Racing Chain GB520XSO-120 120-Links Gold X-Ring Chain with Connecting Link.DID 520ERT2 – 120 link Gold Chain with Connecting Link.Renthal C294 R3-2 O-Ring 520-Pitch 120-Links Chain.

What is the difference in motorcycle chains?

Chains basically come in two categories: unsealed or standard roller chain, and sealed or O-ring chain. Unsealed chains are commonly found on vintage bikes, small-displacement economy rides and off-road motorcycles. … Standard chain is just a series of plain bearings made of metal links and nothing else.

Are O-ring chains better?

The O-rings encircle the pin bushings, and rest between the outer link and inner link plates. This seals chain grease in the pins and rollers, maintaining better lubrication for longer. Because of this, O-ring chains have a reputation of lasting anywhere from 1.5 – 2 times longer than standard, non-O-ring chains.

Are Snell chains good?

Snell Powerlink is a quality brand with low rolling resistance and minimal after stretching, Quadra X-ring gives 50% less friction than an O-ring chain. The chain lasts up to three times longer than a standard motorcycle chain. … The rivets in combination with the hardened links give you an extremely durable chain.

How many miles does a motorcycle chain last?

Don’t clean and lube your chain, replace it more often. It depends on how much rain/sand/grit you ride through in addition to your efficacy and frequency of chain cleaning. I often got 10,000 to 15,000 on a liter bike chain. I often got 20,000 to 25,000 on a VStrom 650 chain with a chain oiler.

Do O-ring chains Rob power?

O-ring chains eat horse power. Over sized chains eat horse power. When you only have 10 – 12 HP to start with, you can’t afford to loose any. But if you have a 50 HP bike, loosing half a HP to an O-ring chain isn’t noticable.

What does 520 mean on a chain?

(3) The size of a chain is designated by a three-digit number (520, for example). The distance from the center of one pin to the center of the next is called pitch. Pitch is represented by the first digit, which is 4, 5 or 6.

Where are EK chains made?

EK motorcycle drive chains are made in Japan with the same precision and innovation as the country’s most famous motorbikes. The company was founded in 1941 and has developed industry-leading chains ever since.

What is Z ring chain?

Z-ring section provides enhanced chain flexibility. Lubricant trapped between plates and lobes of Z-ring keeps the ring lubricated and increases its life. High alloy steel plates and pins. Solid bushing and rollers, shot-peened plates. Pre-stretched chain that is plated gold.

Are XAM chains any good?

X-Ring. X-ring motorcycle chains are more efficient than O-ring ones, which is why they are perfect for the charged environment of a racetrack. They provide less drag and give your motorbike more mileage. One of the benefits an X-ring chain has over the O-ring chain is that it is a better utilizer of lubrication.

Article first time published on

What is the strongest 520 chain?

Monster. The 520MX boasts our highest rated tensile strength among non-sealed chains at 8,930 lbs. Perfect for the beating that chains take during tough, off-road races.

What is the difference between 520 and 530 chain?

A 530 chain on a 520 sprocket will work just fine, a 532 will not. The differance between a 520 and 530 is the width, the roller diamiter and pitch are the same.

Is it OK to use wd40 on bike chain?

You can use WD-40 Multi-Use-Product. It is a water based lubricant that provides the right amount of lubrication to the chain lube. … WD-40 is a great bike chain lube water based lubricant and will not only lubricate the chain well, but will also keep it rust and corrosion free.

Can engine oil be used as chain lube?

Usage of engine oil or grease is not at all recommended over a proper chain lubricant. Grease wont penetrate into the O rings and X rings as compared to chain lubricant. Whereas engine oil lasts only for a few days which reduces the life of your chain and sprocket.

How often should I lubricate my motorcycle chain?

As a general rule of thumb, it’s best to clean and lubricate a motorcycle chain with O-rings at least every 600 miles, while plain chains require more frequent attention.

How often should you tighten motorcycle chain?

Too tight is as bad as too loose, but it’ll only take minutes to get it right. You should check and adjust your chain every 500 miles (805 km), and more often for a dirt bike. It’s also a great time to look for kinks or rust, and to give your chain a quick cleaning and lubrication, too.

What is considered high mileage for motorcycle?

For small sports bikes, 20,000 to 30,000 is on the high side. For larger bikes, 50,000 miles and up is considered high motorcycle mileage. But before you write off any models, consider that a properly maintained bike can last well past 100,000 miles!

What the difference between a 520 and 525 chain?

It may sound ridiculous, but by simply changing your regular 525/530 chain and sprockets to a 520, you’ll gain roughly 1.5hp on the dyno and save nearly a kilogram. … People will bring up the fact that 520 chains will wear out faster than 525/530 chains. Ultimately, if you start to nitpick, yes, they will.

What do the numbers mean on chain size?

Chain types are identified by number; ie. … The digits to the left indicate the pitch of the chain in eighths of an inch. For example, a number 40 chain would have a pitch of four-eighths of an inch, or 1/2″, and would be of the standard dimensions in width, roller diameter, etc.

What is the pitch of 520 chain?

ChainPitchWidth41512.70mm4.88mm42012.70mm6.35mm42812.70mm7.75mm52015.88mm6.35mm

Are O-ring chains quieter?

The O-ring chain will typically be quieter when riding unless your sprockets are worn and/or the chain is out of adjustment.

How long do dirt bike chains last?

A new chain dirt bike chain can last between 700 and 5000 miles. However, it all depends on your riding style and maintenance. Be sure to always ride with a chain that’s in a good condition, because it directly affects the bike’s performance and your safety.

What is a link on a motorcycle chain?

Every motorcycle or bicycle chain contains both an inner and an outer link. The outer link clamps over the sides of the inner ones to create a smooth, consistent chain with each link angled in the same direction. When counting the links, you must count both inner and outer links separately.

Do you need to change sprockets with chain?

Change The Sprockets With The Chain If you determine that your chain is constantly getting stuck and lubrication is not increasing the smoothness of your ride, it’s likely time to get a new chain. However, when you replace your chain, it’s a great idea to replace your sprocket at the same time.

Where Are RK chains made?

100% Made in Japan. RK Chain produces specific chain tools to quickly and easily break 40 and 50 type chains without busting a knuckle.

When did O ring chains come out?

The solution came in 1971 with the development of the O-ring chain. In short, this innovation added a rubber insert between the inner and outer link plates to act as seals to keep dust and debris out, retain lubrication, and reduce metal on metal friction.

Who invented the O ring chain?

Construction. The o-ring chain is named for the rubber o-rings built into the space between the outside link plate and the inside roller link plates. Chain manufacturers began to include this feature in 1971 after the application was invented by Joseph Montano while working for Whitney Chain of Hartford, Connecticut.

Who makes vortex chains?

EK is already the manufacturer of all our Vortex 2.0 chain and we are very pleased with the quality.

Who owns Vortex Racing?

Matt G – President – Vortex Racing | LinkedIn.

Where are Vortex sprockets made?

Rear sprockets, again made in the USA using the highest quality aluminium. 7075 T6 grade alloy is used to manufacture the supersport and superbike rears.

What's the difference between 420 and 428 chain?

The primary difference between 420 and 428 is the pitch of the links. A 130 link 428 chain will be longer (and generally speaking, heavier-duty) than a 130 link 420 chain.