Staining a concrete floor can change the entire feel of a room. It adds color, texture and richness to what might otherwise be viewed as a cold concrete slab. There are different types of stains on the market, including solvent-based, acid-based and water-based stains.

How do you stain brushed concrete?

  1. Step 1: Clean Concrete Driveway. Clean your concrete driveway floors with an organic concrete cleaner and degreaser. …
  2. Step 2: Apply Acid Stain. To apply acid stain, we recommend using a pump sprayer. …
  3. Step 3: Neutralize. …
  4. Step 4: Seal.

Can you stain broom swept concrete?

Decorative concrete surfaces are usually not broom finished. … Stains and dyes are some of the more popular finishes for this type of concrete. You can apply dyes and stains to broom finished concrete too, though.

Can exposed aggregate concrete be stained?

Exposed aggregate can be stained or dyed to shift or change the color upon completion. Exposed aggregate is done by using a chemical retarder on the surface of the concrete during its placement. … It is also a cost effective method of getting a decorative concrete finish.

Can polished concrete get stained?

Although polished concrete floors are stain-resistant, they can still stain if spills are not cleaned promptly. The most common stains we see are fruit juice, wine, vinegar, laundry soaps, and pet stains. These liquids tend to have an extreme pH and can etch the most superficial surface of a floor, requiring repair.

Is Pebblecrete the same as exposed aggregate?

Pebblecrete is concrete that incorporates small pebbles to change its appearance and texture. It’s also known as exposed aggregate.

Can rough concrete be stained?

If the concrete floors are particularly smooth or have been polished, you should sand them before staining. The best concrete surface for staining is rough and porous to allow good color penetration. Smooth, glossy surfaces will prevent all types of stains, even acid stains, from properly sticking to the floor.

Can you paint broom finish concrete?

Concrete and paints are two different kinds of animal. Fortunately paint bonds readily to other materials, including concrete. … However, some heavy-duty epoxy surfaces for flatwork may require a broom finish to be produced when the concrete is being constructed to obtain maximum adhesion.

Can you resurface aggregate concrete?

Exposed aggregate concrete is a decorative finish where the top layer of concrete is removed to reveal the small aggregates beneath the surface. … This means if you have an existing concrete surface that is structurally sound, we can resurface it to look like exposed concrete.

How do you fix a bad broom on concrete?

There are two things you can do fix the rough finish. One is, you could grind or polish the surface which would remove the rough broom finish and smooth the surface of the concrete. Some of the aggregate would be exposed giving you a nice smooth decorative look to your sidewalk and patio.

Article first time published on

Do you seal broom finish concrete?

Sealing a Broom Finish A broom finish can stand up well to the elements, even without being sealed. … Because of this, we recommend that you seal broom-finished concrete so it maintains its intended look. Ask us about spicing up your broom-finished concrete with borders, broomed-in patterns, or even acid or dye staining.

Does water stain polished concrete?

Polished concrete flooring stain resistance Polished concrete floors from Midland Flooring are treated with a penetrating densifier and penetrating stain protection impregnator which are designed to soak into the surface and resist staining from oil, water and grease.

What is the difference between stained concrete and polished concrete?

Stained concrete has a coating on it to make a shine that is very durable. Polished concrete is just that – it’s polished rock and the actual surface is smooth. It’s a process that is designed to look good and last for years like granite and marble.

What do you seal polished concrete with?

Hone and Seal The high gloss finish is achieved by applying a concrete sealer such as our SV45 Polyurethane. The trick to getting an even gloss level is to apply several coats until your coating is thick enough to sit above the concrete.

Is it better to paint or stain concrete patio?

For the ultimate in long-lasting, durable color, choose concrete stain. Because concrete stain doesn’t just sit on the surface of the concrete, but actually penetrates into the pores of the concrete to some degree, your color is not going to peel, chip, or flake.

How soon can you stain concrete after pouring?

New concrete should be fully cured before staining, which takes between 21 and 28 days.

Can you stain textured concrete?

However, you might want to add some color to your stamped concrete. A common question that we get at Concrete Camouflage is: “Can I stain stamped concrete?”. The short answer is: yes, you absolutely can.

How do you paint or stain a concrete fountain?

Paint the concrete with new stain. Leave the stain to dry then add a second coat to saturate the color or to eliminate blotchiness. After the stain fully dries, paint the fountain with a fresh coat of concrete sealer.

How do you make a concrete statue look like marble?

  1. Test if the statue is sealed by applying a few drops of water on its surface. …
  2. Remove dust from your statue with a moist sponge. …
  3. Apply a base coat of latex satin paint. …
  4. Allow to dry and apply a second coat.
  5. Select two colors for the finish. …
  6. Cover a strip measuring 2 inches on your statue using the first finish color.

Can you stain concrete planters?

Concrete planters are cheap, durable and available at almost any home improvement store. … Apply stain to the concrete planter using your preferred method: dabbed on with a rag or sponge for a mottled look, brushed or rolled on for an even look, or sprayed on for a splattered look.

Can you resurface Pebble concrete?

Resurface an Old Pebble Pool Deck It absolutely doesn’t! … From old exposed aggregate to stamped concrete to knockdown coatings to existing kool deck, you can save thousands of dollars in demolition and deck replacement costs by resurfacing instead of removing the old hardscape.

How do you make Pebblecrete look good?

Have you ever thought of resurfacing your sad-looking pebblecrete surfaces with a non-slippery solution that is very simple and cost effective? By spraying your pebblecrete driveway or patio with a spray-on cement, this would enhance the beauty of your home.

Can you resurface Pebblecrete?

Can you resurface Pebblecrete? Yes, resurfacing can be applied to any sound concrete including old pebblecrete. Resurfacing, often called Spray On, can be used for various surfaces and applications including: … and a range of commercial projects that have existing concrete.

How do I remove Pebblecrete?

Simply shatter a small area with a chisel and hammer. Once you have removed a very small section of the pebblecrete you will see either glue residue that will need to be ground off your concrete using a concrete grinder.

Can you paint a Pebblecrete driveway?

These products need to be ordered at your local store’s Special Orders Desk. Unfortunately paving paint and garage paint systems are not compatible with pebblecrete. Your other option is to clean your pebblecrete with a high-pressure washer to remove the mold infestation between the pebblecrete.

How do you resurface over exposed aggregate concrete?

  1. Option One: Use A Surface Coating. …
  2. Option Two: Use A Matting System And Sealant. …
  3. Option Three: Use A Cover System. …
  4. Option Four: Add A Mulch Top Layer. …
  5. Option Five: Add Pavers. …
  6. Option Six: Cover With Thin Brick Strips. …
  7. Option Seven: Paint It. …
  8. Option Eight: Use Tiles.

Can aggregate concrete be painted?

Over time, exposed concrete aggregate can get worn. A change to your landscaping or house color may prompt the desire to paint your aggregate to match. Whatever your reason for painting your aggregate, treat it just like painted concrete to get a solid, durable finish.

What is concrete acid stain?

Acid stains are one of the oldest ways to color concrete. Most acid stains are a mixture of water, hydrochloric acid, and acid-soluble metallic salts. … The acid in the stain lightly etches the surface, allowing the metallic salts to penetrate more easily.

How do you paint bond to concrete?

Epoxy primer: Although it provides a really thin finish, it creates a very strong bond to concrete. Epoxy primer is actually able to absorb into the concrete and creates a great grip on the surface of the concrete for painting.

What is broomed concrete?

Sometimes called brushed concrete, a broom is used to create a slip-resistant texture on the surface of the concrete. Concrete finishers have been broom finishing for about as long as there has been concrete. Broom finishes have been used for many years and provide a durable, high-traction surface.

What can I use to make my concrete smooth?

Smooth the surface with a steel trowel after it’s partially hardened. Hold the trowel almost flat and swing it in large overlapping arcs while applying pressure. Float the concrete when you’re done grooving and edging (Photo 6).